02:22So here is our cup holder, bottle holder, tan holder, whatever.
02:27So we'll take it off.
02:31Quite a lot of stringiness in there.
02:33There's also quite a few layer shift lines, especially getting into the top here, that's
02:37a pretty huge one.
02:39I just suppose that I, at some points, didn't adjust this because still, not to the point
02:44where I haven't either modified this to take these larger wheels or got on some of those
02:49little bearings to put under this so it can actually spin.
02:52So I have to do it every while again.
02:53Let's just manually spin this around.
02:55Let's let some of the filament come off.
02:59Let's just take this off.
03:02That's actually releasing quite well.
03:04Normally these ones are quite difficult to release.
03:06I think it's a combination of the glue plus some of the paper making it slightly easier.
03:11Another piece of the base plate that's come off the pin bed.
03:19So that's what's going to come off next time anyway, but it doesn't really matter.
03:22So here it is.
03:24And here is our suction cup.
03:30Put this little piece here.
03:33And that's no good, it seems as whole as slightly too small, but measured it should be perfect.
03:40Slightly goes in, but did not all the way, so I'll probably have to now print another one
03:44of these.
03:45So I could try to either widen the hole or make this smaller.
03:50I think it's probably easier just to print a whole new one of these pieces and that way
03:55I don't have types of plastic or these more microplastics floating around from it.
03:59But I imagine it's probably not good to be sanding this down, or I guess it's pointing
04:03a file or something.
04:05So let's print a new one of these with a slightly bigger hole.
04:09So here is our new version.
04:13It also printed it slightly slower, so it took a considerable amount of time, longer.
04:17I think this one usually took about 4 hours, that one took about 6 hours.
04:22Less stringing at least, it was a slower speed.
04:25You can see almost all the stringing in the middle there is gone, although there is still
04:30a lot of stringing at the back here.
04:35So you can see some there.
04:37Let's see if this one is as easy to remove as that one.
04:41I think that's actually coming off quite well.
04:44I was worried that it was stuck on there.
04:47So maybe with this PETG, if I wait a day before taking it off, it's better if it's in peace
04:53and it's been ripping off, it's been shortly after printing it.
04:55But yeah, both of these ones, this one I left for two days, one I left for one day before
04:59taking it off.
05:00That's not even that round, that hole in the centre.
05:02So let's see if it does work with the suction cup.
05:07So this one, yeah, still doesn't fit.
05:10I don't know how hard you push, it does not go through.
05:12This one is one millimetre wider.
05:16And it fits, so quite loose.
05:19So this one, yeah, must have just been slightly too small.
05:24Is it quite a big gap now?
05:26This is the suction cup, that.
05:32The suction cup isn't sticking now, things just...
05:36The poised surface isn't good, but though I have started this before.
05:42So let's see whether it can hold where it was supposed to.
05:45So I've just got a can here.
05:50Slightly too big with this size can, so we'll stick for now with a bottle or something.
05:55Because it's a bit smaller, or it can be a smaller can.
05:58So I just remembered some stuff we do have with this bottle.
06:02Still slightly too big for that.
06:05But as for our small can, we've got a small can here.
06:09That one does actually fit quite well.
06:13It's easy to put in because it's got this open area.
06:15And I'm just cutting off all this stringiness as I put this in.
06:20But yeah, that fits quite well.
06:23Easy to get in, it's got a bullet point on it.
06:24So it's not going to fall out by itself unless it's on quite the angle.
06:29Easy to put in, easy to get out.
06:30I've got this back to support it.
06:32I imagine it's probably going to stick quite well.
06:38This is probably just going to clean it up and then I can try it out.
06:57I'll be right back.
06:57Hello, people.
06:58Hello, people.
06:58Music.
06:58Music
07:02We are still about to get out.
Comments