00:00Hey guys, today I am bringing you a mini AWM sniper rifle made of paper.
00:05It is small, delicate and feels great in the hand.
00:07Hug fans, you are in for a treat.
00:10Hang it on the wall or grab it for a quick play.
00:12Totally addictive, if you like it.
00:14Long press the like button so the algorithm pushes my video.
00:19Also hit follow, share and save.
00:21Your support keeps me creating.
00:24Grab an A4 sheet, about 21 by 31 cm and split it into two halves first.
00:29Drop 666 in the comments if you like my videos, thanks a ton.
00:34Fold the paper in half twice, same fold on the second sheet.
00:43Leave about 2 cm at the top, that will be the barrel channel.
00:52Drop the extra paper into the slot.
01:00We need 3 of these in total.
01:03Grab another A4, fold one half the same way as before.
01:12Fold that half and half first.
01:16On the second fold keep top and bottom edges the same way.
01:21Then fold the whole thing in half.
01:24You now have 2 strips, one wide and one narrow.
01:27Fold the wide one in half.
01:28Then wrap the narrow one around it.
01:31Leave 2 cm at the top again, same fold.
01:38The top is too long so trim the excess and tuck the rest into the slot.
01:50Compare, one big, one small.
01:53Make 3 small ones as well.
01:55This A4 will be the barrel, because the sheet is big and hard.
01:59To roll, stick a straw to the edge first, then roll around it.
02:05Slide the barrel in to check width, then glue it in place.
02:12Feed a big piece onto the barrel first.
02:16Then a small one.
02:18Big, small, small again, and another small.
02:24The last big piece goes inside the middle big piece.
02:32Cut another sheet in half to make 2 identical long strips.
02:46Add glue on top first.
02:49Insert one end of the strip into the slot.
02:55Trim the back excess and tuck the tail into the rear slot.
03:15This A4 stays uncut, we will form the stock, the handle of the gun.
03:19I will skip simple steps, just follow along.
03:22Then, let's do it, then go ahead and pull the pieces on.
03:29Let's do it.
03:42We need two of these stocks.
04:08Add glue and insert one on each side.
04:12If the middle feels hollow, sandwich a thick paper spacer inside for a fuller look.
04:18This sheet forms the join between stock and body.
04:21Leave about two.
04:285 cm at the back.
04:29Fold inward, same fold on the other half.
04:36Angle this fold for slope.
04:42Add a dab of glue for strength.
04:47Insert as far back as possible.
04:53The other side goes into the stock.
04:55Cut the sheet in half, half will become the extended barrel.
05:02Size the extension so both barrels slide together snugly.
05:07Then glue to fix.
05:09Join the two barrels into one long tube.
05:14Cut the remaining half sheet in half again.
05:21Fold the strip about 1 cm wide, 7 or 8 times, then trim the extra.
05:27Pinch both ends flat.
05:40Roll the leftover scrap into a thinner cylinder for the bolt handle.
05:44Flatten left and right halves.
05:56Trim to size and cut off excess.
05:58This sheet becomes the rear stock plate.
06:03Check size first.
06:05Only the scope is left.
06:21A 6.5 cm wide, 21 cm long strip rolled into a cylinder.
06:24Take a sheet and divide it into 8 equal strips.
06:26Group every 4 together.
06:28Glue the 4 strips sets end to end to make 2 long bands.
06:36Glue one end of a band and wrap it around the cylinder.
06:40Do not roll too tight.
06:53Wrap the second band on the other end.
07:00Because the scope is angled, gently pull it outward to the right spot.
07:05About 2 cm wide, fold 4 or 5 times to build thickness.
07:35Check width, trim excess, and insert all parts into their slots.
07:48This AWM is now complete.
07:50Did you get it?
07:51If you enjoyed this, please follow, share and save.
07:54See you next time!
Comments