00:03Welcome, we will solve problem 8.43 from the book Statics by the authors see and
00:09Johnston, regarding the topic of friction, the statement says the following: two blocks
00:158 kilograms a b are connected by a rod of negligible mass knowing that the
00:20The magnitude of a horizontal force p applied at c increases slowly from zero. Determine the
00:26value of p for the motion to be imminent and what that motion is when the coefficient of
00:31static friction between all surfaces is u sub s equal to 0.4 u sub s is equal to
00:420.5 se
00:43It asks to analyze the force p necessary for the movement to be imminent; this means that the assembly is
00:51It will move or it will rotate, so for part a a free body diagram is drawn for
00:58visualize
00:58The forces that interact with the system are the load p and for each block acts the
01:05The concept of transmissibility is applied to the normal reaction and the frictional force.
01:13Move the forces along their line of action and position them at the points shown on the screen.
01:21This is done to better visualize that there is a distance from point c and that the
01:28The force acts perpendicular to that distance; using the diagram, the
01:34The summation of moments pivoting on the positive sign convention is proposed in a counterclockwise direction
01:40Regarding this, six forces act: the weights, the friction forces, and the reactions.
01:48Normal distances are obtained by relating the vertical dimensions to the 25° angle
01:54degrees by means of the tangent trigonometric function, like terms are reduced, it is known
02:01that the frictional force is the product of the normal force and the coefficient of friction is applied
02:07This concept will be factored into the previous equation, adding the normal forces of blocks a and b in turn.
02:16Both factored terms are grouped on one side of the equation, generating expression number 1a
02:23The equilibrium condition is then applied on the y-axis, and the positive convention of
02:29The sign is proposed with an upward direction on the vertical. Four forces act: the reactions.
02:35normals and twice the weight since both blocks have the same mass, the normals of a
02:42side of the equation obtaining expression number 2 below the congruence of
02:49The units of the values that the problem provides as input data are substituted and operated on in 1 and 2
02:58By doing this, a system of two equations is formed; solving it yields the magnitude of the
03:05normal forces and multiplying them by the coefficient of friction, which is 0.4, yields
03:13The frictional forces then apply the equilibrium condition on the x-axis
03:21positive sign convention is proposed with a rightward direction on the horizontal line.
03:26three forces, the load p and the friction forces, p is isolated, obtaining an expression as a function of
03:34Known values, unit consistency is verified, the data is substituted and operations are performed when
03:42The coefficient of friction is 0.4; a force equal to 62 points 78 newtons is needed for the
03:50If movement is imminent, a similar analysis is done in the next section using the equations
03:581 and 2 are replaced by the data provided in the problem, which are the same as those provided by the employees
04:05Previously, the only thing that changes is the coefficient of friction; they are replaced, they are operated again.
04:16form a system of two equations; in this particular case, it is known that
04:24Normal forces cannot be negative because this suggests that they go in the opposite direction, which indicates
04:31The negative sign means that the frictional force of block b is so great that it produces rotation about it.
04:38At this point, therefore, block a ceases to have contact with the surface; a new one is drawn
04:45free body diagram showing what was said above; the diagram is drawn at an instant
04:52After block A ceases to be in contact with the surface, it can be seen that the coating has been applied.
05:00concept of transmissibility to the weight of the block using the diagram the summation of moments is applied
05:07pivoting at b, the positive sign convention is proposed counterclockwise with respect to b.
05:16two forces that produce a rotation: the weight over a distance of 200 millimeters by the tangent of 25 and
05:23The load p over a distance of 100 millimeters is solved for p. Note that the weight has been expressed as
05:30he
05:30The product of mass and gravity is used to verify the consistency of units of the known data.
05:36They are replaced and operated so that the movement is imminent with a coefficient of friction of 0.5.
05:44It requires a force of 73.19 newtons, thus solving the problem, and that would be all if the video was helpful.
05:52of
05:52Useful, don't forget to subscribe