- 2 days ago
Category
🛠️
LifestyleTranscript
00:00Now, I just found this. This is probably from the 90s. Model number 9074.
00:14I'm going to take it apart again because I wanted to see if I could get some sort of battery replacement.
00:30The screws here are pretty easy to take the casing off. Just one here.
01:00I'm trying to do this one-handed.
01:20Yeah, they had bits in here.
01:22I think you would just must have lost all the bits, but I do have the straight and the Phillips still.
01:41So, once you take this case off, you just go along the crack here.
01:57But I'll have to take that clip out first.
02:00And the first time I did, everything exploded.
02:08Just put a small straight screwdriver in there.
02:12Lift up on the pin.
02:22Like so.
02:30That'll just come off.
02:37And then you can open it up.
02:46The switch here was on this part.
02:51You can see where it goes on there.
02:53And there's the motor.
03:09Johnson motor.
03:14And be careful with this part here.
03:17But I'll show you how the gears come in.
03:21I might have lost a couple pins, but we'll see what happens.
03:28I'll look for them later.
03:31I'll take this plastic.
03:33It's like a washer out.
03:36One sec.
03:38Just like that.
03:41Then you'll see the red.
03:48Gears on top.
03:49There's three of those.
03:51And that was on top of the motor.
04:07So, we'll just leave that there.
04:09And you have this part here that's got a gear on the top.
04:28And there's the pins.
04:30So, yeah.
04:31The first time I opened this up, it exploded.
04:35So, you'll see there.
04:41The first thing you want to do is put.
04:47Let's see if I can get a light in there.
04:51You can see in there.
04:52The first part will be this right here.
05:15Now, that'll set right in there.
05:17Let me get these tweezers.
05:19Got tweezers with a light on it.
05:46Better.
05:47So, that part goes in first.
05:51Now, we'll put the pins in.
05:55And you want to put the pins in on the flat side.
06:00Not in the grooves.
06:02So, we'll take one.
06:09See, we don't want that.
06:11You have to turn this when you put it in.
06:32And then, it'll just fall in place.
06:46Okay.
06:47Let's try that again.
06:48So, right there.
06:53So, right there.
07:02You have to hold that.
07:04Just lay it down.
07:20In there.
07:22In there.
07:27In there.
07:34Now, on some, for some reason, I couldn't get all three sides.
07:39So, I'm thinking this might have worked like this.
07:43There were six pins.
07:48Three here, maybe.
07:50And three there.
07:51And none there.
07:53Because it was so tight.
07:55The pin.
07:56It looks like it would fit in.
07:59But, as you can see.
08:00See, it goes towards the groove.
08:18Is there another one?
08:20No, I'm going to have to find them.
08:23But, uh.
08:25I have a screwdriver that's magnetic.
08:27See, now, I'll.
08:33See, you just won't.
08:34I tried to push it in.
08:36I tried to pull that back.
08:39So, I'm just going to have the two.
08:42And then, when I find the rest.
08:44You can see I got the two in each side.
08:49And that'll be all on that for now.
08:55So, next will be this part.
08:57Let's see if I can just use the tweezers on this.
09:07And I'm going to turn it.
09:08And it goes down.
09:14Sets down.
09:17And these three.
09:19Pins here.
09:21We're going to put the black.
09:22I guess it really doesn't matter.
09:26But, since I've seen the red on the top.
09:30The black must go down here.
09:34They're the same size.
09:36If I can get it in the tweezers.
09:46If I can get it in the tweezers.
09:46Fingers did a better job than the tweezers.
10:00I don't know if there was any kind of grease in here.
10:14So old that it dried up.
10:16Okay.
10:35So you see.
10:36There's the gears.
10:37Let's see the next part.
10:45Would be.
10:48This here.
10:50With the gear.
10:53We're going to set that straight down in there.
10:55Okay.
11:08After that.
11:09Now we'll put on the.
11:14Red.
11:17Gears.
11:25Now we can probably put that.
11:36Plastic.
11:39Washer to hold it in.
11:41On this model.
11:43Anyhow.
11:43There isn't.
11:44That other.
11:46I've seen another video.
11:48Where there was another metal plate.
11:50This one didn't have it though.
11:53So we go over here.
11:55To the shell.
12:08Take that button.
12:12And I believe the.
12:18Little ridge here.
12:21Was on the bottom.
12:25And then the wheel will go in.
12:35That's how you can tell.
12:36Also is.
12:39The.
12:39It's only going one way.
12:46So if it went.
12:47It.
12:47Yeah.
12:48See it won't go in that way.
13:02Just like that.
13:04Where the wires are coming down.
13:06Now you can see.
13:07These clips.
13:08See that one clip.
13:10Right there.
13:10It's corroded.
13:12That came.
13:13Right off the battery.
13:16That came.
13:17Off the battery.
13:19And I'm going to show you.
13:20The battery number.
13:21Right now.
13:32See it blew a hole in there.
13:34Unable to find a number.
13:44But that would.
13:45Just lay in here.
13:49Okay.
13:50So let's try to close this up now.
13:53Well first we'll put that.
13:56Gear on the motor.
13:57And then I believe.
14:13The open space on the motor.
14:17Is down.
14:18It only goes one way or the other.
14:20And the slots probably go and see there's slots in this plastic wheel.
14:35So I'm just going to pause this a second.
14:40Noting that the gold contacts here are on top.
14:47Switch.
14:48Put it to bottom.
14:50Actually I had to hold that together.
14:59While I put the screw in.
15:03So you get the same spring here.
15:07On and off.
15:10And whatever battery or ring to put in there.
15:13I forgot what the voltage is.
15:15But there's.
15:16But there's.
15:18Basically.
15:19The same voltage.
15:21As the other ones.
15:22You could probably find a video.
15:24And if you had this model.
15:28It probably would work.
15:31Now to put the top back on.
15:33And that will only go on one way.
15:41Because the pin has to go back in.
15:44So there's where the pin goes in.
15:46And let's match it up.
15:51And let's match it up.
15:53Just like that.
15:55Holds match up.
15:58Gear goes in.
15:59And I believe the pin will go in.
16:11And I believe the pin will go in.
16:11Just like that.
16:20See if we can.
16:24Unless it's in upside down.
16:26Yeah.
16:30So it's going to be going in a down.
16:32At least this pin anyway.
16:38No.
16:43It's got to be the other way then.
16:52Add that on backwards.
16:55Turn it around.
16:57Yeah that looks.
17:01More like when I found it.
17:03Now let's see.
17:03If that goes up or down.
17:06It'll go up probably.
17:09There it is.
17:14Alright.
17:18Finish tightening the screws.
17:27This actually goes in.
17:31Both ways too.
17:34Trying to.
17:35I would think the cord's going down.
17:37If you put this on the wall.
17:39So.
17:39It must go like that.
17:44But it'll click in either way.
17:47Yeah.
17:47If I remember right.
17:48It goes in.
17:51Alright.
17:53There you have it.
17:55Take care.
17:56Thanks for watching the video.