00:12Offset alignments are generally used to create geometry for road channel lines or adding road
00:17lanes. The advantage of using offset alignments is that they remain linked to the center line
00:24alignment and can be edited to include changes in offset with transitions. We don't have to convert
00:31polylines or worry about what happens if the main alignment is moved.
00:38Click on McConister Boulevard and on the ribbon choose offset alignment.
00:43Offset alignments are linked to their parent alignment. They'll have an automatic name which
00:49you can override if you wish. Deselect from start and set the start station to zero.
00:56We don't want to create offsets along the existing part of the road which are the negative station
01:01values. We'll create one offset on the left and one offset on the right. Both will be set to 12
01:09feet
01:09from the center line. At the bottom of the dialog set the alignment style to offsets and set the
01:18label style to no labels. Click on the widening criteria tab. Here you can add automatic widening
01:30around curves. This will adjust the offset alignments to create flared widening around the curves
01:36based on standards defined in a design criteria file or by specifying manual widening.
01:44Don't select these options. Deselect use design check set.
01:52On the create offset profile tab we can tell Civil 3D to create offset profiles for our offset alignments
01:59based on a design centerline profile. We're using McConister Boulevard layout 1 profile.
02:06We can superimpose these offset profiles onto an existing profile view.
02:13Change the superimpose onto profile view to McConister Boulevard 1.
02:18This will draw offset profiles in that view.
02:25The profiles can be generated with a crossfall from the centerline profile
02:29as our road will be crowned. Set the cross slope to minus 2%.
02:36Each new profile will be given an automatic name.
02:41Set the profile style to basic and click OK.
02:47The offsets have been added to the drawing and can be managed from Prospector.
02:53In Prospector expand alignments and expand offset alignments.
02:59Expand an offset alignment and expand to profiles.
03:04Here you can see that it has created a profile for the offset alignments.
03:10When we create offset alignments they are linked to the main centerline alignment.
03:14If we move the centerline now to the left offset alignment.
03:19Widening can be used to create lay-bys and parking areas or to add widening lanes.
03:24Select the offset alignment and on the ribbon choose add widening.
03:28On the command line it is asking if you want to create a new alignment or to add to the
03:33existing one.
03:34Select yes.
03:36We often use a new alignment for lay-bys where we want to maintain a crossfall to the channel line
03:41and have a positive grade to the back of the lay-by.
03:46Set the start station for the widening to 1250.
03:50And for the end station enter 1500.
03:57The widening offset will be 24 feet as measured from the centerline.
04:05Choose the side left and the offset parameters dialog will be called up.
04:11You can change the offset, the start and end stations or you can enter a region length.
04:22You can change the transition parameters at entry and exit.
04:28For the transition parameters the transition type controls the geometry of the alignment at the transition.
04:36If you set the transition type to linear you can choose the taper input type of by length or by
04:42taper ratio.
04:44If you set the transition type to one including curves you get options to modify the curve radii.
04:53Try editing the curve radii to see the changes on the screen.
05:00Review the other options for different transition types.
05:05Both transitions should be set to linear by length
05:11with a transition length of 100.
05:16Changes to the widening are applied immediately. There's no option to save them.
05:21You can also create widening to an offset alignment graphically.
05:26Make sure dynamic input is turned on for these edits.
05:32Select the right hand offset alignment.
05:35Click the plus symbol to create a new widening region.
05:39If you want to use the right hand grip, it will automatically widen it out.
05:43Use the diamond grip to drag the transition to line up with the opposite lay-by.
05:49Press escape to clear your selection and then select the offset again.
05:53Now you'll see two plus grips, one for each region.
05:57Split the right hand region again.
06:01Use the diamond grip to move the new widened region into position.
06:07Use the arrow grip for the third region to move the offset back in, type 12 as the widening value.
06:16Now select the circle grip on the transition and then use the smaller circle grips
06:21to change the length of the transition.
06:26Adjust the position of the transition using the diamond grips.
06:33Now if you select the arrow grip in the central region and type 12 as the offset,
06:38it will reset the widening back into a single drawing to this curve on the Macaulister Boulevard alignment.
06:49Pan and zoom the drawing to this curve on the Macaulister Boulevard alignment.
06:54As we drive around this curve we want the left side of the road to be at minus two percent,
06:59but the right side to tilt up at plus two percent.
07:04We can add superelevation to a road by assigning it to a centreline alignment.
07:09We'll learn more about that during detailed design.
07:13But here we're going to use our offset alignments to add a manual superelevation.
07:18You can use this method to transition crossfall from one side of a road to another,
07:23perhaps for allowing a change in the drainage.
07:26Select the right hand offset alignment and then on the ribbon choose offset profile properties.
07:33In the profile properties, click on the offset parameters tab.
07:38In here we can add cross slope regions.
07:42Click the plus to add a new region.
07:45For the station of the first region, on the command line, type 100.
07:52The slope at this point will be minus two.
07:56On the curve at station 300, here the slope will be plus two as we are transitioning.
08:05As we come along the road and we approach the end of the curve,
08:08we want to transition back to a crowned road.
08:11The next station will be at 1100.
08:16This will remain at two percent.
08:19And then finally for the last region, add station 1500.
08:25The road here will transition back to minus two at this location.
08:31You can review the regions in the dialog and edit them in here.
08:35Click OK to save the changes.
08:39Go to the profile view.
08:41The horizontal curve on the alignment is here.
08:45And if we look at the profiles, you can see that the two cyan profiles are the offset profiles.
08:53You can see where they transition apart at the start of the curve.
08:57The left side is at minus two percent all the way through.
09:00But the right side transitions to plus two percent and then back to minus two percent at the end of
09:07the curve.
09:09If I make a change to the centerline profile, then when I make the edit,
09:14the right side of the curve, then I need to see it.
09:14I'm looking at the right side of the curve.