Master Autodesk Revit Wall Modeling with this complete step-by-step tutorial covering professional architectural wall design, advanced wall editing, compound wall construction, wall layers, wall junctions, and architectural detailing.

This tutorial covers 15 essential topics to help you develop professional Revit modeling skills, from basic wall types to advanced wall configurations and architectural components.

Topics Covered in This Tutorial:

1. Create Wall Types in Revit
2. Creating a Compound Wall
3. Unlocking Wall Layers
4. Assigning Functions to Wall Layers
5. Working with Boundary Layers and Wall Joins
6. Control Wall Junctions
7. Embed Walls
8. Attaching Walls to Floors and Roofs
9. Editing Wall Profiles
10. Creating Slanting and Tapered Walls
11. Editing Assigned Wall Taper Settings
12. Creating a Baseboard and Coping Stone
13. Importing Profiles to Create a Sweep Type
14. Using Wall Reveals
15. Adding Architectural Columns

Who Should Watch?

- Architects and Architectural Designers
- BIM Modelers and BIM Specialists
- Revit Professionals
- Civil Engineers and Construction Professionals
- Students learning Autodesk Revit

Learn professional architectural wall modeling techniques and improve your Autodesk Revit BIM workflow.

Subscribe to Autodesk 786 for more free Autodesk Revit, Civil 3D, BIM Modeling, Architecture, and Infrastructure Engineering tutorials.

Learn. Model. Design. Build Your BIM Skills

#AutodeskRevit #RevitWallModeling #RevitTutorial #WallModeling #BIMModeling #RevitArchitecture #CompoundWalls #RevitWalls #ArchitecturalDesign #WallLayers #WallJoins #RevitBIM #BIMArchitecture #Autodesk #RevitTraining #ArchitecturalModeling #BIMWorkflow #Autodesk786

Category

📚
Learning
Transcript
00:00Music
00:10As walls are system families, we cannot load a new wall type into a project,
00:15so we must duplicate an existing wall type and edit it to suit.
00:21If I select one of the existing external walls we have in the model,
00:24we can see from the Type Selector at the top of the Properties palette
00:28that this is a basic wall and a generic 8-inch wall type.
00:35The other wall types that are available from the Type Selector
00:38have all been created within the template that was used to build this model from.
00:44The wall that we're going to create requires an external insulation system on metal stud,
00:49and that's not available in the Type Selector to us,
00:52so we would duplicate an existing wall and create it.
00:56If only the external wall is selected,
00:58I'll choose Edit Type from the top of the Properties palette
01:01to access the wall's type properties.
01:05And across the top we can see the type name here, generic 8-inch,
01:09and next to it the Duplicate button that we'll use to create our new wall type.
01:14So we'll go ahead and click Duplicate,
01:17and then we'll assign the new name of external wall EIFS on metal stud.
01:26And we'll select OK to create that new wall type.
01:32So now we need to edit the assembly of the wall to add in the extra layers.
01:36And to do this, from the Type parameters on the Construction panel,
01:41we'll click Edit next to Structure to access the Edit Assembly settings.
01:48So here we can see the layers that make up the current wall.
01:51And at the bottom of the box we can click the Preview button to enable the preview,
01:56which will make it easier for us to see what happens as we add our new layers in.
02:03So we'll start by changing the thickness of this existing layer to 6 inches.
02:08And before we add the new layers, we can see at the top it's labeled Exterior,
02:13and at the bottom is the Interior side.
02:16We can see we have the layer numbers showing their order,
02:21and then below that we have the buttons to insert and move new layers around.
02:25So we'll start by inserting the new layer,
02:27and this will appear in layer 2, just above our existing layer.
02:31We'll set the thickness to be 3 quarters of an inch.
02:38And we can see that appear in the preview on top of the existing layer.
02:43So now we'll add our next layer in.
02:45So we'll click Insert, we'll get another layer.
02:48And this is going to represent our external installation.
02:51So we'll change this to 2 inches thick.
02:55And we can see that appear in the preview.
02:57So now we'll move that up to above the core boundary.
03:01So making sure we have layer 2 selected.
03:05From the buttons beneath the layers, we'll click the Up button to move this above the core boundary.
03:13And we can see in the preview now the green line,
03:15which is indicating the location of the core boundary within the layers of the wall.
03:21So now we need to add the internal finish.
03:24So we'll select layer 5, the core boundary layer.
03:28And we'll choose Insert, which will add a new layer just above that.
03:32So we'll click the Down button to move that below the core boundary.
03:37And we'll set its thickness to be half an inch.
03:43So now we can see that has appeared in the preview.
03:46And we can see the green line for the lower core boundary.
03:50And obviously the upper one as well.
03:52So next, we'll assign the materials into those layers that we've just created.
03:58Looking at the material column, we can see they are currently set to have the By Category material.
04:04And to change this, we'll need to launch the material browser and select a new material.
04:10So we'll select By Category on layer 1.
04:13And from the ellipses button that appears, we'll launch the material browser.
04:17We can see there's a lot of materials available in this project.
04:21So to make it easier, we'll use the search bar at the top and we'll search for Insulation.
04:27And from the materials that then appear in the list, we'll choose the EIFS Exterior Insulation material.
04:35And we can see its properties here, but we don't need to make any changes.
04:39So we'll click OK and this will be assigned into layer 1.
04:43And we can see that in the preview as well.
04:47So now for the next layer, which is layer 3, we'll click By Category again.
04:50And then from the ellipses button, we'll launch the material browser.
04:54And this time, we'll search for Plywood.
05:01And then we'll choose the Plywood Sheathing material.
05:04And click OK to assign this on to the next layer.
05:07And once again, we can see that appearing in the preview as well.
05:12So for layer 4, we'll choose By Category and again launch the material browser.
05:17And this time, we're going to search for the stud material.
05:21And we'll choose the metal stud layer.
05:24And once again, we'll click OK to assign this into that layer.
05:29So for the final layer, this is going to be our gypsum wallboard.
05:32So once again, we'll launch the material browser and search for gypsum this time.
05:38And then we'll select the gypsum wallboard material and click OK to assign that to layer 6, our final layer.
05:46And then we can see in the preview that we've got all of those materials applied onto the layers.
05:52So finally, we now need to assign the function into each layer.
05:56And we can see that they're currently all set to structure.
06:00And if we select the function on layer 1, we get the dropdown list.
06:04And we can see that we've got five functions here.
06:07Structure, substrate, thermal layer, finish 1 and finish 2.
06:12And in the parenthesis, we can see the numbers 1 to 5.
06:16And these denote the priority order for when we make junctions between different walls.
06:21Number 1 is the highest priority and we'll cut through objects of a lower priority to create the join between
06:29those different walls.
06:30So for our exterior insulation, we'll choose finish 1, which has the priority of 4.
06:36For the plywood sheathing, we'll assign that in to be the substrate function.
06:41The metal stud layer, we'll leave that as structure with the priority of 1.
06:45And for the gypsum wallboard, we'll set that to be finish 2 with the priority of 5.
06:52So now that we have all of our layers created with their thickness and materials, we'll click OK to save
06:58those changes.
07:01We're back in the type properties, so we don't need to make any more changes here.
07:04We can see we have the exterior function already selected from the wall that we duplicated.
07:10So we'll choose OK once more to now save the changes to this wall type.
07:16And that's been applied to the wall that we had selected when we started this process.
07:21However, if I click off of this wall, we'll see that it's still shaded in grey as they were originally.
07:27And this is due to the view being set to a coarse detail level.
07:31So to change this, we'll go to the view control bar at the bottom of the view.
07:36And then we'll select medium from the detail level.
07:40And then zooming into the wall here, we can now see the layers that we created onto that wall type.
07:46And they're now being displayed in the view.
07:50So this leaves us now just to change the rest of the external walls in this model.
07:54So we'll select one of those.
07:57And then from the right click menu, we'll choose select all instances visible in view.
08:04And this will now select the remainder of those external generic 8 inch walls.
08:10So now from the type selector, we can scroll up and we can find the external wall EIFS or metal
08:18stud that we've just created.
08:19And it's also in the most recently used types list.
08:22So we just need to select that.
08:25And then that wall type is applied to these walls.
08:29So we'll click in space to deselect them.
08:31And now zooming in, we can see the external walls that we will be editing.
08:36We'll change the brick material for a masonry stone.
08:39And then add a brick soldier course between the floor levels around 12 feet from the bottom of the walls.
08:45So we'll select one of the walls.
08:47And then from the top of the properties palette, we'll choose edit type to access the walls type properties.
08:55As we're going to change the main material, we shall rename the wall first.
09:01So at the top of the type properties, choose rename.
09:05And then we'll enter the name exterior stone with brick soldier on metal stud.
09:13And then we'll click OK to accept the new name.
09:18Now we need to edit the assembly of the wall.
09:21So to do this, we'll click edit from the type parameters next to the structure parameter.
09:27And this will open up the edit assembly settings.
09:30And we can see the layers that make up the wall.
09:32They're reflected in the preview.
09:34And it's the top layer here, layer one, that we will change the material of.
09:38So we'll click on masonry brick.
09:40And then open the material browser from the ellipses button.
09:44And then from the project materials list, we'll choose masonry stone.
09:48And click OK to assign this onto layer one.
09:52And we can see that that's now updated in the preview window.
09:56And now we need to create the brick soldier course within layer one.
09:59And to do this, we need to use the modify vertical structure tools,
10:03which are currently greyed out and not available to us.
10:06And the reason being is the preview is currently in a floor plan.
10:10So from beneath the preview, we'll choose the section view.
10:15And then we can see the preview window update to a section.
10:18And those modify vertical structure tools are alive and available to us now.
10:24It can be useful to manipulate the preview window.
10:27So from the top right corner of the edit assembly,
10:30we can set the sample height to say 10 feet.
10:33And we'll see this update with the wall in the preview.
10:36And then from the right click menu, we can access zoom tool.
10:39So we'll choose zoom to fit to now fill the preview window with our wall.
10:44Our storage of course is actually going to be a bit taller than 10 feet.
10:47So let's set that back to 15 feet.
10:50And then from the navigation bar,
10:51we can also access the same zoom tools and choose zoom to fit.
10:56And then we're ready to start using some of those modified vertical structure tools
11:01to create our soldier course.
11:02So first one we'll use is split region.
11:05So let's click on that to enable it.
11:08And now as we go over the preview window,
11:10we can see our cursor has changed to look like a knife.
11:13And as we move across the assembly there,
11:16we can see the edges of the layers highlighting.
11:19And if we then click,
11:21it will add a split line into that highlighted layer
11:24and split it into two separate regions.
11:27We could add more split lines to create multiple regions.
11:34We've added this split line into the metal stud layer
11:38and we can see that reflected on the thickness of the layer list there.
11:43So actually to remove that,
11:45we'll click merge regions.
11:47And this will allow us to go over the preview
11:50and click on the split line itself,
11:52which will then delete it and merge those regions back into one
11:56and create one layer.
11:58So now we need to add the split lines to create our brick soldier course,
12:02which is in layer one up here.
12:04And it's going to be near the top of the wall,
12:0612 feet approximately from the bottom.
12:08So we'll click on split region to enable that
12:11and making sure we're on layer one,
12:13we'll click to create the first split line somewhere near the top of the wall.
12:19And then we'll add a second split line above this one
12:23so that we've got three regions.
12:25The middle one will become our brick soldier course.
12:28So now we want to edit the dimensions to place it accurately.
12:32And to do this,
12:33we need to click modify from the modified vertical structure tools
12:37to enable us to select the split line.
12:40And then we can come and edit the dimension.
12:42So let's set this to 12 feet.
12:44And then we'll select this upper split line for the top of the soldier course.
12:49And we'll set this to be eight inches
12:52so that we've got an eight inch soldier course
12:54that starts 12 feet from the bottom of the wall.
12:59So now we'll click on modify to disable it.
13:03And we need to create the material for the brick soldier course.
13:06And to do this, we'll insert a new layer into the layer list.
13:10So we'll click insert and we'll add a new layer at the top of the list.
13:14We'll change its function to match the masonry stone.
13:18So finish one.
13:20Then we'll click by category and open the material browser from the ellipses button.
13:25And find the masonry brick soldier course in the list of materials.
13:29And click OK to assign that into our new layer.
13:33We won't change thickness as we're going to assign it.
13:36So from the modified vertical structure tools, click assign layers.
13:41And now as we go over the preview window, we can see it highlight different regions.
13:46And once the brick soldier course region is highlighted,
13:48we can click to assign that layer and that material into that region.
13:54So click assign layers to switch it off.
13:57And now we'll choose another layer in the list so that we can see in the preview window
14:01where we've assigned in the brick soldier course material to the region that we created with the split region tool.
14:08So that finishes creating the brick soldier course.
14:11And we'll click OK to save these changes.
14:15Then we'll click OK again to apply these changes to the model.
14:21And now we can see the external walls have updated.
14:24We can see the masonry stone material along with the bricks.
14:28Looking at the projecting walls at the rear of the building,
14:30we can see that they align to the underside of the roof as shown in the image here.
14:37And ideally, we would like the finish layers to continue up in front of the roof to give us a
14:42cleaner junction.
14:44We can achieve this by unlocking the top of the finish layers in the wall type
14:50so that they can extend separately to the rest of the wall.
14:55So in order to do this, with one of the walls selected,
14:59we'll click Edit Type from the top of the properties.
15:02And then we need to access the assembly again.
15:04So we'll choose Edit next to the structure parameter.
15:08And we can see we have the finish layers here.
15:11And our preview is still in section view.
15:13So we'll choose zoom in region to zoom into the very top of the wall.
15:20And it's these three layers here that we need to extend up in front,
15:25separate to the main structure of the wall.
15:28So from the Modify Vertical structure, we'll click Modify.
15:32And now we can click the top edge of those layers.
15:36At which point we'll be presented with a padlock,
15:38which we can then click to unlock the edge of those layers.
15:41So let's repeat this for the other two layers here.
15:44Clicking on the top edge and unlocking the padlock.
15:48And that means that these will now be able to extend separately
15:52to the main structure of the wall.
15:54So now click Modify to disable it.
15:57And we'll click OK to save these changes.
15:59And OK again to apply these to the wall.
16:03Now as we zoom in, we can see we have two drag controls at the top of the wall here.
16:08And if we drag the outer one, just the finishes are extended.
16:13And looking in the properties, we can see the unconnected height.
16:16And below that, we have a top extension distance parameter
16:21for the layers that we've unlocked, which is just those finishes in front of the wall.
16:25So let's select the roof.
16:27And we can see that this is the generic 12 inch roof type.
16:30And looking in its properties, we can see the thickness is one foot thick.
16:35So now we'll select the walls that we want to extend in front of the roof.
16:39So using the control key, we can multiple select those walls.
16:45And then in the properties, we can see the top extension distance currently varies
16:51because of the different walls we have selected.
16:52So we'll set them all to be one foot.
16:56And then once this is applied, we can see those finishes
16:59the core boundaries aligning up to the top of the roof.
17:01And gives us a value within the wall assembly.
17:04And the function assigned to the wall layers determines how walls will clean up
17:08when they join in the model.
17:10All layers positioned between the core boundaries will always continue through
17:15to meet the layers within the core boundary of the wall that they are joined with.
17:20Layers outside the core boundary will be cut to allow this to happen.
17:24Therefore, the positioning of the core boundary is an important factor in achieving the required
17:30junction between walls.
17:33The layers are also assigned a function and priority which will influence the clean-up too.
17:39There are five functions with their associated priority shown in parenthesis,
17:45with priority 1 being the most important, and therefore priority 5 being the least important.
17:51The function indicates what the layer may be used for, but when walls join,
17:57it is the priority which controls the clean-up.
18:01Looking at the wall detail floor plan, we'll use zoom region to zoom into the office at the top of
18:06the floor plan.
18:08And we can see that we have a partition coming up to meet the exterior wall.
18:13It's showing us the metal stud layer of this partition going through the wall board and the furring
18:18to meet the CMU layer of the external wall.
18:21And this junction works fine and is what we would expect.
18:25On the outside of the wall, there is a section of wall that has the same granite panel finish on
18:31metal stud.
18:32And this will be used for a screen wall, so it doesn't require the same structural or thermal properties as
18:38the main external wall.
18:40This wall does have to join the external wall though.
18:43So I'll select it and using the control at the end of the wall, we'll drag this over the external
18:48wall.
18:48And it doesn't really matter where as Revit would join the two walls according to the settings in the type
18:54properties.
18:55And we can see the junction that it's created here.
18:58It shows the metal stud and the air layers of the screen wall coming right through to meet the CMU
19:04layer of the main external wall
19:05and cutting through the insulation layer in the process.
19:09So let's look at how Revit is forming this junction.
19:13In this image, we can see the junction that we currently have, which is the metal stud and air layers
19:18of the screen wall
19:19cutting through the insulation to meet the CMU layer of the main external wall.
19:25The junction required is for the metal stud layer to meet the edge of the insulation in the external wall
19:31and for the thermal air layers of both walls to merge.
19:35Currently, the main external wall has its core boundaries positioned around just the CMU layer.
19:41And in the screen wall, they're positioned around both the metal stud and air layers.
19:46And hence, the layers contained in the core boundary are cutting through all of the layers outside the core boundary
19:52to meet each other and form the junction.
19:56We will need to move the core boundaries to incorporate the layers that we want to control in the junction.
20:01So for the screen wall, they need to be moved in to contain just the metal stud layer.
20:07And for the main external wall, they need to move out to incorporate the insulation layer too.
20:13But if we just move the core boundaries, we will still end up with the wrong junction as illustrated here.
20:19And this is because the priority of the layers also needs to be altered to give us the junction that
20:24we're looking for.
20:26This means changing the insulation in the main wall to be a substrate with a priority of 2.
20:31In the screen wall, the air gap layers must change from substrate to thermal air with a priority of 3.
20:38And the metal stud layer must change from structure with a priority of 1 to be a substrate with a
20:44priority of knit type to access its type properties.
20:48Then we'll click Edit next to the structure parameter to access the wall assembly.
20:54Looking at the layer list, we can see the core boundaries either side of the air layers and incorporating the
21:00metal stud layer.
21:02The air layers need to be moved outside of the core boundary.
21:06So I'll start by selecting the top air layer, layer 3, and then click the up button to move it
21:13above the core boundary.
21:16Then we'll select layer 5, the lower air layer, and click the down button to move this one outside of
21:22the core boundary.
21:23And we can see in the preview now, the green lines indicating the location of the core boundaries either side
21:29of the metal stud layer.
21:32While we're in the walled assembly, let's change the function and priority of the air and metal stud layers.
21:38We'll start by changing the upper air layer, layer 2, from substrate to thermal air layers with a priority of
21:453.
21:46We'll repeat this for layer 6, the lower air layer.
21:50And then for the metal stud layer, which is layer 4, this is currently set to structure with a priority
21:56of 1.
21:56And we'll change it to substrate, which has a priority of 2.
22:02Now we'll click OK to save those changes, and OK once more to apply them to the walls in the
22:08model.
22:09So now we can see that's changed the junction, but we need to edit the insulation in the main external
22:15wall to complete the junction.
22:18So we'll select this main wall, and again we'll choose edit type from the properties palette to access its type
22:24properties.
22:26And then click edit next to the structure parameter to access the assembly settings again.
22:31So here we can see the insulation layer is outside of the core boundary, but needs to be within those
22:36core boundaries to give us the correct junction.
22:39So this time I'll select the upper core boundary layer, which is layer 4, and click the up button to
22:46move it above the insulation.
22:49And now we can see it's within the core boundary, along with the CMU layer.
22:53So now we just need to change the function of the insulation layer.
22:57And we'll change this from being thermal air layer with a priority of 3, to a substrate with priority of
23:032.
23:04So this should now give us the junction that we need.
23:07So we'll click OK to save those changes, and OK to apply them to the walls in the model.
23:13And now we can see we had the junction that we wanted, with the metal stud layer of the screen
23:17wall meeting the insulation layer,
23:20and with the air layers of both walls having merged to be a continuous component around the junction.
23:26An alternative scenario would be if the screen wall was built after the external wall,
23:31and therefore we didn't want the components in the core boundaries to interact or to create any kind of join
23:37between the walls.
23:39And we just wanted the screen wall to finish against the granite panel of the existing external wall.
23:46So to achieve this, we would need to stop the walls from creating a joint.
23:51To show how to do this, I'll select the current screen wall that's got the join.
23:56We'll make a copy of it.
23:57So from the Modify ribbon tab, we'll choose Copy, and then click to pick the wall up.
24:03And we'll move it across to the left here, and then click to place it down.
24:08I choose Modify to finish the copy command.
24:10And we can see that it created the same junction as it had done previously.
24:16So to stop this from happening, we'll select the wall.
24:20And then hover over the grip at the bottom of the wall where the junction is made.
24:25And then from the right click menu, choose Disallow Join.
24:30Now, when we deselect the wall, we can see that they no longer join.
24:35And the screen wall is just overlapping the existing external wall, with no attempt being made to create any junction.
24:42If I reselect the screen wall, we can see at the end of the wall, we'll have the symbol here
24:48to indicate that the joint is disallowed for this end of the wall.
24:51And we could click this symbol to re-allow the join.
24:55However, we just need to cut the screen wall back to meet the external wall.
25:00So to do this, from the Modify ribbon tab and the Modify panel, I'll choose Trim Extend Single Element.
25:07And then select the edge of the external wall to be the boundary.
25:11And then we'll choose the side of the screen wall that we want to keep.
25:15And now we can see that we have that just butted up to the external wall without any junction being
25:20made.
25:23So there we can see how the core boundary and the function and priority can affect the clean-up of
25:28walls,
25:29and how different walls can meet to create different detailed junctions.
25:40Draw it around this office.
25:44There are a few junctions here, so where this partition comes around the corner with the door,
25:49and then this third one joins on, if I zoom in a bit closer,
25:53we can see that it's not properly joined with these lines that are going through the junction.
25:59So, in order to force this to give us the junction that we're looking for,
26:03we can use the Wall Joins tool.
26:06And to do that, we'll go to the Modify ribbon tab,
26:10and then from the Geometry panel, we'll choose Wall Joins.
26:15Now we can see, as we move the mouse around the view,
26:18it highlights the different wall joins, and we'll choose this one here to edit.
26:25Now, looking at the Options bar,
26:27we can see that we have the configuration set for it to be Buck jointed.
26:34We could swap it to Mitered, and this would give us a junction like this,
26:38but that would still not be correct, so we'll leave it on Buck jointed.
26:43And then we'll click the Next button to cycle through the different options for this junction.
26:49As we can see, each time we click Next, it's showing the position of the different components within each wall,
26:56and putting them into different locations to give us different junctions with each option.
27:01And we can keep cycling through until we get one that we think is correct for our junction.
27:06I think this one will work fine, so now we'll choose Modify to finish the Wall Joins tool,
27:11and we can see it's created the junction between these walls that we chose,
27:14and will give us a much more viable junction.
27:18Coming further along to the end of the wall, we can see that we have quite a sharp corner,
27:23and it would be good to control this somehow, otherwise, in the real world,
27:27it's likely to get chipped and broken quite easily if someone bumps into it.
27:32So once again, in the Modify ribbon tab, we'll choose the Wall Joins tool from the Geometry panel.
27:38And now we'll move over to the corner of the wall that we want to modify,
27:42and select it to give us the options.
27:45So we can see how the walls are joined currently at the moment,
27:49and clicking Next we can cycle through those.
27:53We can choose Mitre, but that won't help us, so we'll choose Square Off,
27:58and we can see that what that will do is it will reduce a 90 degree angle to one of
28:02the walls for our join.
28:04And we can choose the next option to choose which of the walls is actually squared off at the end.
28:11So I think we'll go with this one, as it will give us the best junction.
28:15So now we'll just click Modify again to finish the Wall Joins tool.
28:19So there we can see that the Wall Joins tool allows us to control exactly how the components join together
28:25in different walls.
28:27And it also allows us, if I select the main wall, we can see this is the stone on CMU
28:33wall type,
28:33and we can also see where it is cut around the brick panel.
28:38Now if I select the Brickwork panel, we can see that this is a separate wall to the main wall,
28:43and it is the exterior brick on CMU wall type.
28:47I'll change the Top Offset parameter of this wall, so from the Properties palette in the Constraints panel,
28:53we'll change the Top Offset parameter to minus 4 feet.
28:58And we can see this wall reduces in height once that's applied,
29:01and that the main stone wall has followed,
29:03which shows the relationship between the embedded wall and its host.
29:08We need to create a similar brick panel around the two columns of windows on the right-hand side of
29:13the elevation,
29:14and we'll do this by creating a new brick wall and embedding it into the stone wall.
29:20First, we'll copy the existing windows to the clipboard,
29:23in case we need to paste them back into their location as they may get deleted during the embedding process.
29:29We have a selection set already created in the model for those windows,
29:33so we'll go to the Manage ribbon tab,
29:36and then from the Selection panel, we'll choose Load Selection,
29:40and then select the Windows set and click OK,
29:44and then we can see those windows are now selected in the view.
29:48So from the Modify ribbon tab, we'll go to the Clipboard panel,
29:51and we'll choose Copy to Clipboard, so that we have those in case we need them later on.
29:57Next, we need to create the brick wall to embed into our main stone wall,
30:01and to do that, we'll first go to the Floor Plan view, Floor 2.
30:08Once the Floor 2 view is open, we need to zoom in to the right-hand end of the view,
30:13so from the navigation bar, I'll choose Zoom Region,
30:16and draw a region around the upper right-hand end of the building.
30:22Here we can see we have two reference planes created to help us position the new wall.
30:26They're shown in red here.
30:28And we'll draw the wall between these two reference planes to encompass the windows.
30:33So to do this, we'll go to the Architecture ribbon tab,
30:36and from the Build panel, we'll click the Wall tool to start creating the wall.
30:41And then from the Type Selector, we'll find and choose the Exterior Brick on CMU Wall Type.
30:48And then once we have this selected, from the Options bar, we'll change the Location line to be Finish Face
30:55Interior.
30:57Now, starting at the upper reference plane, we'll click where this intersects with the interior face of the wall.
31:05And then we'll move the mouse down to the lower reference plane, and click again to place the wall.
31:11And straight away, we can see that we have a warning, which can be ignored,
31:15but that warning is telling us that we have overlapping walls,
31:18and that one may be ignored when Revit finds room boundaries.
31:22And it's also telling us that we could use the Cut Geometry tool to embed one wall into another,
31:29which is what we will do.
31:31So we'll choose Modify from the ribbon to cancel the wall creation tool.
31:35And now from the Modify ribbon tab, under the Geometry panel, we'll choose the Cut Geometry tool.
31:43Now in the view, select the main stone wall which will be cut,
31:46and then click on the Brick on CMU wall as the object to cut the main wall with.
31:53So now we can see straight away that the overlapping stone wall is no longer there,
31:57as it's cut around the brick wall.
32:00However, we do have a join line at either end of the brick wall,
32:04which we can clean up by using the Join Geometry tool.
32:08So from the Modify ribbon tab in the Geometry panel, we'll click Join Geometry.
32:13And then we'll select the main stone wall,
32:16and then the brick panel wall to join those two together.
32:20And we can see that those lines have now disappeared.
32:24Fortunately, we can also see that the windows have remained in their place,
32:28so we may not need to paste those windows back in from the clipboard that we copied.
32:33So now let's go back to the exterior perspective view.
32:38And we can see that we have our brick wall that's embedded into the main stone wall,
32:43although it's only currently going up to floor 3.
32:46So now we'll select the brick panel wall,
32:49and we'll change its properties to match the existing brick panel that we have on the left-hand side here.
32:55So now in the Properties palette, we'll find the top constraint parameter,
32:59and we'll change it from up to level floor 3 to up to level roof.
33:05And then once that's applied, we can see that change its height,
33:08and we can see the existing windows remain in place,
33:11so we won't need to paste those in from the clipboard.
33:14So now we just need to adjust the top offset parameter to match the existing brick panel.
33:21And to do this, we'll use the Align tool.
33:23So from the Modify ribbon tab on the Build panel, we'll choose Align.
33:28And now you may need to use the Tab key to cycle through to select the top of the existing
33:33brick panel as the reference.
33:36Once we have that, we can click on the top of the wall instead.
33:40In order to attach the wall to the underside of the floor, there are two ways to do this.
33:45One is the automatic way when we're actually creating or editing the floor.

Recommended