Skip to playerSkip to main content
I thought 20mm wheel spacers would be right for the front of my 2017 Tesla Model S. After test-fitting them, I switched to 15mm up front and kept 20mm in the rear. Here's the honest why.

I started with measurements, not guesses. A steel ruler against the fender showed a 20mm gap to the tire edge on both axles, so 20mm spacers looked like the flush answer, and that's what I fitted first. On the car, the front sat farther out than I wanted. That's the part measurements can't tell you: the final look only shows up in person. So the front went to 15mm, the rear stayed at 20mm.

The clearance math that made this safe: factory studs measure about 38mm, wheel pockets about 27mm deep. With a 15mm spacer the studs extend about 23mm; with 20mm, about 18mm, both well inside the pocket, so the wheel seats completely flat. No cutting, no grinding, fully reversible. I also checked the caliper-to-spoke clearance at the measurement point shown in the video, useful if you ever upgrade to larger calipers, since the spacer pushes the wheel 15mm out from the spokes.

Looking back, I'm glad I test-fitted 20mm first. The trial fit told me what I actually wanted instead of trusting numbers alone.

SPECS ON MY CAR
• 2017 Tesla Model S, stock wheels, 5x120, CB 64.1, M14x1.5
• Tried: 20mm front & rear → switched front to 15mm
• Final: 15mm front, 20mm rear
• BONOSS Forged Active Cooling spacers, AL6061-T6, hub-centric, bolt-on
• Studs ~38mm, wheel pockets ~27mm, no stud cut
• Torque: 140 N·m (BONOSS Grade 10 nuts) / 175 N·m (factory nuts)

Product page: https://www.bonoss.com/product/bonoss-forged-active-cooling-hubcentric-wheel-spacers-pcd5x120-cb64-1-al6061-t6-for-tesla-model-s
Series:
▶ Full install + stud clearance → https://youtu.be/GRrurwx2byc
▶ How to choose the size → https://youtu.be/ANX0DsGa51o

#wheelspacers #tesla #models

Category

🚗
Motor
Transcript
00:00I thought 20mm wheel spacers would be the right choice for the front of my 2017 Tesla Model S.
00:06But after trying them, I changed my mind. The wheels sat farther out than I wanted,
00:11so I switched to 15mm up front and kept 20mm in the rear. Here's why I made that decision.
00:17Before choosing the spacer size, the first thing I did was take some measurements.
00:21I used a steel ruler to measure the gap between the fender and the outer edge of the tire.
00:26I checked both the front and rear wheels, and the gap was about 20mm at both ends.
00:32That gave me a useful starting point for choosing the spacer thickness.
00:35So, I decided to try 20mm spacers first to see how they would look on the actual car.
00:41Because measurements can only tell me so much.
00:44The final fitment still comes down to how the wheels sit relative to the fenders,
00:48and that's something I needed to see in person.
00:50Once I saw the 20mm setup on the car, I felt it push the front wheel out farther than I
00:55wanted.
00:56I kept the 20mm spacers in the rear.
00:58The final setup became 15mm up front and 20mm in the rear.
01:04I didn't choose those numbers because every Tesla Model S needs a smaller spacer in front
01:09and a larger one in the rear.
01:10I chose them because that was the combination I preferred on this particular car.
01:15Your result may be different, especially if your wheels have a different offset or width,
01:20or if you're running different tires.
01:21That's why I recommend evaluating the front and rear separately instead of automatically
01:26using the same thickness at all four corners.
01:29Of course, choosing a spacer isn't just about appearance.
01:33On my Model S, the factory studs measured about 38mm long,
01:38and the wheel pockets measured about 27mm deep.
01:41Those numbers helped me understand the setup.
01:43With a 15mm spacer, the studs can extend approximately 23mm beyond the spacer's mounting face.
01:51With a 20mm spacer, that figure is approximately 18mm.
01:56Both numbers, 18 and 23mm, sit well under the 27mm recess in the wheel.
02:03That means the wheel drops down and seats completely flat against the spacer,
02:08giving us 100% wheel-to-spacer contact between the wheel and the flange.
02:12No cutting, no grinding, and absolutely no permanent modification to the vehicle.
02:18And if I ever decide to pull the spacers off,
02:21the Tesla Model S goes right back to completely stock, not a single trace left behind.
02:26I also checked the brake caliper-to-spoke clearance at the measurement point shown here.
02:30This means that when I want to upgrade to larger calipers,
02:33I don't have to worry about the inside of the wheel spokes rubbing against my modified calipers.
02:38Looking back, I'm glad I tried 20mm before settling on 15mm.
02:43The test fit helped me understand what I actually wanted instead of choosing a size
02:47based on numbers alone.
02:49For this 2017 Tesla Model S, 15mm in front and 20mm in the rear was my preferred combination.
02:57If you're planning a similar setup,
02:59check out our Tesla Model S wheel spacer video in the description.
03:03Subscribe to Bonas for more real-world wheel fitment tests and installation guides.
03:07Bonas for more real-world wheel fitment tests and installation guides.
03:11Bonas for more real-world wheel fitment tests and installation guides.
03:11Bonas for more real-world wheel fitment tests and installation guides.

Recommended