Skip to playerSkip to main content
What size wheel spacers fit a 2017 Tesla Model S? On this car the answer was 15mm front and 20mm rear, but we got there by measuring and test-fitting, not by copying someone else's setup.

SPECS ON THIS CAR
• Vehicle: 2017 Tesla Model S (stock, 5x120, CB 64.1, M14x1.5)
• Fender gap (tire edge to fender): 20mm front / 20mm rear
• Tested: 20mm front & rear → owner preferred 15mm front
• Final: 15mm front, 20mm rear
• Spacers: BONOSS Forged Active Cooling, AL6061-T6, hub-centric, bolt-on
• Stud length ~38mm, wheel pocket ~27mm, no stud cutting needed

⏱ CHAPTERS
0:00 20mm went on first, then this happened
0:35 Step 1: pick your fitment goal
1:17 Step 2: measure the fender gap
2:10 15 vs 20: what 5mm actually changes
2:58 Front and rear don't have to match
3:30 Watch the full install next

FAQ
Q: What size spacers for a stock Model S?
A: On this 2017 car, 15mm front / 20mm rear achieved the look the owner wanted. Measure your own fender gap first.
Q: Should all four corners be the same size?
A: Not necessarily, measure each axle separately.
Q: Does a thicker spacer always look better?
A: No. This owner preferred 15mm front after seeing 20mm test-fitted.
Q: Can I copy this setup?
A: Use it as a starting point; confirm with your own wheel offset, tire size, and the stud-clearance check in our install video.

Product page: https://www.bonoss.com/product/bonoss-forged-active-cooling-hubcentric-wheel-spacers-pcd5x120-cb64-1-al6061-t6-for-tesla-model-s
Series:
▶ Full install + stud clearance → https://youtu.be/GRrurwx2byc

#wheelspacers #teslamodels #fitment #bonoss

Category

🚗
Motor
Transcript
00:00Choosing the right wheel spacer size isn't just about pushing your wheels farther out.
00:04On this 2017 Tesla Model S, we tried a 20mm spacer on the front,
00:09but the owner felt the wheels sat farther out than desired, so we switched to 15mm.
00:15The final setup is 15mm up front and 20mm in the rear.
00:20In this video, I'll show you how to choose a spacer size based on your fitment goals,
00:25your wheel measurements, and the clearances you need to verify.
00:27Before choosing a number, decide what you want your car to look like.
00:31Are you aiming for a more flush appearance, with the tire sitting closer to the fender line?
00:36Or do you prefer a more conservative setup with less outward projection?
00:40A wheel spacer moves the wheel outward by approximately its own thickness,
00:44but the final result also depends on the original wheel offset, wheel width, tire dimensions, and fender shape.
00:51That's why copying another owner's spacer size doesn't always give you the same result.
00:56Start with your current fitment and your target, not with the thickest spacer available.
01:01Next, measure where your wheels sit right now.
01:04Place a straight steel ruler flush against the edge of the fender.
01:08Then measure the gap between the outer edge of the tire and the fender.
01:11At the front wheels, this gap is exactly 20mm. It's also 20mm at the rear.
01:17Theoretically, therefore, installing 20mm spacers, both front and rear, should achieve a perfect,
01:25flush fitment for this 2017 Model S.
01:28So we first installed 20mm wheel spacers on the front and rear wheels.
01:33Checked the position, and the owner decided it pushed the front wheel out farther than desired.
01:37So we changed the front to 15mm and kept 20mm at the rear.
01:42Let's compare the two sizes used in this project.
01:45A 15mm spacer moves the wheel outward by approximately 15mm.
01:51A 20mm spacer moves it outward by approximately 20mm.
01:55That gives us a nominal difference of 5mm.
01:595mm may sound small, but it can make a visible difference depending on the wheel, tire, and fender geometry.
02:06On this car, the owner preferred the 15mm front setup after seeing the 20mm test fit.
02:12The takeaway isn't that 15mm is always better.
02:16It's that the right size is the one that meets your goal while maintaining the required clearances.
02:21Another important point, the front and rear don't automatically need the same spacer thickness.
02:27This Model S ended up with 15mm in front and 20mm in the rear.
02:32Your front and rear fitment may differ because of the original wheel specifications, body shape,
02:38tire dimensions, and your preferred look.
02:40Measure each axle separately, then step back and evaluate the car as a whole.
02:45If you want to see the installation process in more detail,
02:48watch our Tesla Model S stud clearance and fitment check video next.
02:53Subscribe to Banas for more real-world wheel spacer tests and installation guides.

Recommended