Skip to playerSkip to main content
Installed 15mm front and 20mm rear wheel spacers on a 2017 Tesla Model S, with the stud clearance measured on camera, no stud cutting, and every fitment check that matters before calling the job done.

The question every Model S owner asks first: do you need to cut the factory studs? On this car, no, and here's the proof. Factory studs measure about 38mm from the hub face, and the wheel pockets measure about 27mm deep. With a 15mm spacer the studs extend about 23mm past the spacer face; with a 20mm spacer, about 18mm. Both sit well inside the 27mm pocket, so the wheel seats 100% flat, metal to metal, with zero cutting, zero grinding, and a fully reversible bolt-on setup.

⏱ TIME CHAPTERS
0:00 The fast answer: no stud cut needed
0:33 Measure first: fender gap, studs, wheel pockets
1:46 Why 15mm front, 20mm rear
3:01 Install + torque (140 Nm / 175 Nm)
3:43 Full lock-to-lock clearance check
4:30 Recap: the no-cut checklist

SPECS ON THIS CAR
• Vehicle: 2017 Tesla Model S (stock, 5x120, CB 64.1, M14x1.5)
• Spacers: BONOSS Forged Active Cooling, AL6061-T6, hub-centric
• Front: 15mm | Rear: 20mm
• Stud protrusion after install: ~23mm front (15mm), ~18mm rear (20mm)
• Wheel stud pocket depth: ~27mm
• Lug nut torque (BONOSS ISO Grade 10 nuts): 140 N·m
• Factory wheel nut torque: 175 N·m
• Caliper-to-spoke gap: 15mm stock → 35mm after spacers

FAQ
Q: Do I need to cut studs for 15mm or 20mm spacers on a Model S?
A: Not on this car, 38mm studs minus spacer thickness stays under the 27mm wheel pocket. Measure your own wheel to confirm.
Q: What torque do I use?
A: BONOSS Grade 10 nuts at 140 N·m; factory wheel nuts at 175 N·m. Two passes, star pattern.
Q: Will it rub?
A: Full lock-to-lock test shown at 3:43, no contact at either size, at stock height.
Q: Is it reversible?
A: Yes. Pull the spacers and the car is back to stock, no traces.
Q: Re-torque?
A: Check both torque specs after the first 100 km / 60 miles.

Product page: https://www.bonoss.com/product/bonoss-forged-active-cooling-hubcentric-wheel-spacers-pcd5x120-cb64-1-al6061-t6-for-tesla-model-s

Next in this series:
▶ How to Choose the Right Size → https://youtu.be/ANX0DsGa51o

Disclosure: this video shows products from our own brand, BONOSS.

#teslamodels #wheelspacers #bonoss

Category

🚗
Motor
Transcript
00:00A wheel spacer can bolt onto the hub and still have a clearance problem.
00:03On this 2017 Tesla Model S, the factory studs measure about 38 millimeters long,
00:10while the wheel pockets measure about 27 millimeters deep.
00:13We tested a 20 millimeter spacer on the front,
00:16then switched to 15 millimeters because the wheels sat farther out than the owner wanted.
00:21In this video, we'll check stud clearance, wheel seating,
00:25and the fitment checks that matter before calling an installation complete.
00:28This Model S started in stock condition.
00:31The final setup uses 15 millimeter spacers up front and 20 millimeter spacers at the rear.
00:37We didn't choose the spacer size based on a chart alone.
00:40The first thing we did was take some measurements.
00:42Here's a simple method.
00:44Place a straight steel ruler flush against the edge of the fender.
00:47Then measure the gap between the outer edge of the tire and the fender.
00:51At the front wheels, this gap is exactly 20 millimeters.
00:55It's also 20 millimeters at the rear.
00:57Theoretically, therefore, installing 20 millimeter spacers, both front and rear,
01:03should achieve a perfect, flush fitment for this 2017 Model S.
01:08We actually test fitted a 20 millimeter spacer, checked the position,
01:12and the owner decided it pushed the front wheel out farther than desired.
01:16So we changed the front to 15 millimeters and kept 20 millimeters at the rear.
01:20We'll show you the measurements behind the fitment.
01:23But remember, these results apply to this car, and this will set up, not automatically, to every Model S.
01:30Before installing a spacer, don't just look at its thickness.
01:33You also need to understand how far the factory studs extend and how much clearance the wheel provides behind its
01:40mounting face.
01:40On this car, we measured approximately 38 millimeters of factory stud length and about 27 millimeters of depth in the
01:48wheel stud pockets.
01:49Here's the basic calculation.
01:51With a 15 millimeter spacer, the studs can extend approximately 23 millimeters beyond the spacer's mounting face.
01:58With a 20 millimeter spacer, that figure is approximately 18 millimeters.
02:03Both numbers, 18 and 23 millimeters, sit well under the 27 millimeter recess in the wheel.
02:10That means the wheel drops down and seats completely flat against the spacer,
02:15giving us 100 percent metal-to-metal contact between the wheel and the flange.
02:20No cutting, no grinding, and absolutely no permanent modification to the vehicle.
02:25And if you ever decide to pull the spacers off, the Tesla Model S goes right back to completely stock,
02:31not a single trace left behind.
02:33Now let's check the mounting surfaces.
02:35The hub face and the back of the wheel need to be clean and free of debris that could prevent
02:40proper seating.
02:41For this 2017 Model S, the fitment specifications we're checking are a 5 by 120 bolt pattern,
02:48a 64.1 millimeter center bore, and M14 by 1.5 hardware.
02:54Place the spacer onto the hub and verify that it seats flat.
02:58Don't use the fasteners to pull a misaligned part into place.
03:01If the spacer rocks, binds, or leaves a visible gap at the mounting face, stop and find the cause before
03:08moving on.
03:09For this installation, the final combination is 15 millimeters in front and 20 millimeters in the rear.
03:15We first tried 20 millimeters on the left front.
03:18The owner preferred a less aggressive front fitment, so we switched to 15 millimeters.
03:23The rear stayed at 20 millimeters, and the right side followed the same final front and rear setup.
03:29This is a bolt-on spacer setup, so there are two separate interfaces to verify the spacer-to-hub connection
03:36and the wheel-to-spacer connection.
03:37The Bonas ISO-grade 10-lug nuts installed here are tightened to a torque of 140 Nm, while the factory
03:45nuts are tightened to a torque of 175 Nm.
03:49Before calling the job complete, check the basics one more time.
03:53First, confirm that the spacer sits flat against the hub and the wheel sits flat against the spacer.
03:58Second, verify the correct hardware and torque for both connections, using the instructions for the exact components installed.
04:06Finally, check for interference between the wheel, brake components, and any nearby suspension parts through the relevant range of movement.
04:14If you're planning a similar setup, check your own wheel design and spacer specifications rather than copying these measurements blindly.
04:22Subscribe to Bonas for more real-world fitment tests and installation details.
04:28Upbeat is assigned to the shop.יןixonac
04:29phat.com McConaughey
04:29Q-y Int Wind Step 1 Innovate

Recommended