00:00This video is intended to demonstrate the LoRa Wireless Distributed IRO Data Acquisition Tut
00:06orial using the E90-E95SL Series D2
00:17To ensure the demonstration proceeds smoothly, we have prepared the following materials
00:28First, we configure the radio module
00:30Install the antenna onto the E90-D2-400 cell 30
00:35Connect the E90-D2-400 cell 30 to the USB-2RS485 converter
00:40Note that the RS485 connection must follow a 2A and B to B wiring
00:45Connect the E90-D2-400 cell 30 to the power supply
00:49Connect the USB-2RS485 converter to the computer USB port
00:54Connection completed
00:55Set the DIP switch on the side of the radio to configuration mode as shown
01:04If using E95-E96 radio
01:07Use the mode button
01:08To switch the radio to configuration mode
01:11Adjust M0 and M1 indicators as shown
01:14M0 off, M1 on
01:17Indicates the radio has entered configuration mode
01:20Open the RF setting E20 to E9XSL software on the computer
01:24Select the corresponding serial port
01:27Open the serial port
01:29Click Get
01:30The default parameters of the D2 will be read
01:33You can use default parameters or modify module address and channel
01:37In this tutorial, only the module address is changed to 1
01:41Other parameters remain unchanged
01:44Click Write
01:45The host software shows write successful
01:48Set both M0 and M1 DIP switches to ON as shown
01:51At this point, the radio configuration is complete
01:55Next, configure the distributed IORO
01:59Connect the antenna to the M31
02:01Connect the M31 to the power supply
02:04Connect the 2-wire sensor to the AI1 channel of the distributed IORO
02:09Insert one end of the Ethernet cable into the LoRa wireless distributed IORO
02:14And connect the other end to the computer Ethernet port
02:17Power on the M31
02:21Open Computer Settings
02:23Go to Network and Internet
02:25In Advanced Network Settings, change the computer IP to Subnet 3
02:29In this tutorial, it is set to 192.168.3.4
02:34Note, the IP address must not be the same as the LoRa distributed IORO
02:39Open the distributed IORO configuration software
02:42Click the top left corner to select the Ethernet adapter
02:46Choose the Ethernet IP address just configured
02:49And switch the interface to Ethernet
02:55Click Search to find the device
02:57Click the Discover device
02:59You can view the Modbus address of the LoRa distributed IORO here
03:03Record the Modbus address as 1
03:06Modify the wireless parameter
03:08Set the module address to 1
03:11Keep other parameters as default
03:13Click Save parameters and restart the device to apply changes
03:17At this point, the LoRa distributed IORO configuration is complete
03:21Next, perform acquisition testing
03:25Open Modbus pull on the computer
03:27Click Connection
03:28Select Serial port
03:30Select the serial port corresponding to the E90 radio
03:34Note, baud rate 9608N1
03:38Click Setup
03:40Click ReadWrite definition
03:42Set Slave ID to 1
03:44Function Code 04 PLC Register Area 3
03:48Register Address 0
03:50Quantity 1 Red AI 1 Only
03:53Click OK
03:57You can see that Modbus pull
03:59Has successfully read the AI1 data collected by the LoRa distributed IORO
04:02You can see that Modbus pull has successfully read the AI1 data collected by the LoRa distributed
04:03IORO
04:04Clickbank and run down to the left theUR ==
04:04You can see the Examination in order lockup
04:04Take confirm the desired customization
04:04type in effect you'll find your desired
04:05If you can see the Hello
评论