00:00Assalam-o-Alaikum. This is an error of F4 in the kit.
00:08In this, the compressor is not turned on and an error of F4 occurs immediately.
00:14Let's see what is the problem with this and why an error of F4 occurs.
00:19This kit is being used in Orient, Pell, Kenwood and Chengang-e-Araba.
00:26I will turn on the kit and see the error of F4.
00:34I have set the temperature to 16 degrees.
00:37This is the blower motor.
00:39An error of F4 is occurring but the indoor is being turned on.
00:44The outdoor is not being turned on.
00:46In this, two lights are blinking.
00:51Two lights are blinking and an error of F4 is occurring.
00:55Now, I will turn it off and see the error of F4.
01:03Now, I will remove the sensor.
01:10I have removed the sensor.
01:13First of all, you know that there are three sensors in this.
01:18I have already made a video on this.
01:20This sensor is for the temperature of the end of the condenser.
01:27This sensor is for the ambient temperature.
01:29This sensor is attached to the discharge tube of the compressor.
01:36This is the temperature of the compressor.
01:38If you see the catalog of this sensor, it shows the error of this sensor.
01:47I will check this sensor.
01:49I think the sensor is fine.
01:51Still, I will check it.
01:53This is the movie of the sensor.
01:55You can see the complete detail of the sensor on it.
01:59I have kept it at 200K.
02:06I will check it.
02:07First of all, I will check the meter.
02:10You can see the reading of the meter.
02:17The reading of the meter is 38K.
02:19This is how the jack is installed.
02:22This is how the jack is installed.
02:24This is the sensor.
02:26This is the SMD.
02:29I will put it on the buzzer.
02:32I will put it on the buzzer.
02:37The buzzer is coming to one side of the SMD.
02:39It is not coming to the other side.
02:40I will check it.
02:42I will check the SMD at 20K.
02:45I will check it at 20K.
02:47I will check it.
02:49This is dead.
02:52This is dead.
02:54This is dead.
02:56This SMD is dead.
02:58I will change the SMD.
03:00I will change the SMD.
03:02I have switched on the soldering iron.
03:09The problem is that the soldering iron is not being used.
03:15Because there is a plastic here.
03:16This will burn.
03:17Now I will take it out.
03:18Because if I do this work, it will burn.
03:22If any brother wants to learn your work,
03:25If any brother wants to learn your work,
03:26Then you can come and learn from us.
03:30So that you can learn your work.
03:31So that you can learn your work.
03:36I have removed this for this.
03:39I will change this SMD.
03:41I have shown you in the on camera that you can take this off.
03:46I have shown you in the on camera that you can take this off.
03:47You see, we also remove this.
03:49You see, we also remove this.
03:51Now we will do its SMD change, now we have put its SMD, now we will put its sensor, we
04:07have put its sensor, now let's turn it on, let's turn it on and see if the error of F4
04:12has been cleared or not, it will be known now, see I have turned it on, if you like the video
04:23then like it and subscribe to our channel if you are new, but see the error of F4 has
04:29not been removed yet, now let's see what other problems it has, see it is still there,
04:37wait a minute, wait a minute, I have turned it off, in this one side it was not fully soldered
04:46due to which it is soldering, it is soldering a little fast, otherwise its temperature is
04:54low, see this, now see here, this soldering has been done, now let's see if this error
05:04has been done or not, let's put this sensor, we have re-soldered it properly, it was not
05:11soldered, the problem of iron is a little, sometimes it happens, see now I will put it
05:17again, I have done it, now I will turn it on from here, see this compressor is now ours,
05:28see this, these three lights have been checked, the error is over, it was the error of F4,
05:38which we have now cleared, the error of F4 has been cleared, our three lights are ok,
05:46its motor and its compressor are also on, now let's turn it off, if you like the video
05:55, then like it, share it with your friends, if you are new to the channel, then subscribe
06:01to the channel, thank you for watching the video, goodbye.
Comments