00:00Assalam-o-Alaikum, this is a 1-tonne Greek kit.
00:05The problem with this kit is that when the compressor starts,
00:10the RPM goes up a little and then it stops immediately.
00:15There is no error in this.
00:17We have installed the whole setup.
00:19Now we will run it and test it.
00:21We will show you what the problem is.
00:23After that, we will see which fault is there and how it is repaired.
00:28I will show you.
00:31Now we will run it.
00:33As soon as I plugged it in,
00:38I turned it on with the remote.
00:42Now it is on with the remote.
00:45Now it will run after some time.
00:48The compressor is installed.
00:52The motor is on.
00:54See the compressor.
00:56The starting of the compressor is not good.
00:58It starts very slowly.
01:01After some time, when the RPM increases,
01:05when the RPM increases, then it will stop.
01:07See this.
01:09See this.
01:10The RPM is increasing slowly.
01:12See this. The kit is on.
01:14The kit is on. See this.
01:17As soon as the RPM increases,
01:20See this.
01:22See this.
01:23After some time, it will stop.
01:25See this.
01:26As soon as the RPM increases,
01:29See this.
01:30I put the load like this.
01:32See this.
01:33See this.
01:34It has stopped at the same time.
01:36See this.
01:37It has stopped.
01:38But on the kit,
01:40See this.
01:41There is no error on the temperature.
01:44See this.
01:45It has stopped.
01:46See this.
01:47The lights are blinking.
01:49But see this.
01:50See this.
01:51You can see its 16.
01:53See this.
01:54But the kit is not off.
01:56The compressor is off.
01:57Let's see what is the problem in this.
02:01We have removed the kit.
02:03From its PCB box,
02:05from its cover,
02:06we have removed the heatsink from below.
02:08It is completely out.
02:10Now, I will tell you that
02:12in this case, if there is such a fault,
02:14then you have to check
02:16what all things have to be done in this matter.
02:18I will show you this on the screen now.
02:20Because you will not be able to see it properly from here.
02:22I try that if you can see it from here,
02:24then it is better.
02:26If not, then I will show you there.
02:28What is the problem in this?
02:32In this, the main thing is that
02:34if you have such a fault in this matter,
02:36that the compressor is turned on and off,
02:38or there is such a problem,
02:40then whatever work you are doing,
02:42then you should know this first
02:44that which thing we will check in this
02:46If there is a fault in this,
02:48then there will be a fault in this.
02:50So, look at this.
02:52These two ICs are installed in this.
02:54We have to check all the SMDs of this.
02:56First of all, we will check all these SMDs.
02:58After that, we will check the 330 ohms.
03:00We will get a fault in this.
03:06Yes, look at this.
03:08These are installed in this.
03:10330 ohms.
03:12First of all, we have to check
03:14whether this is correct or not.
03:16Look at this.
03:22Look at this.
03:24Check the reading on the meter.
03:26Turn on the meter light.
03:28This is correct.
03:30Now, we will check
03:32this one.
03:34This is also correct.
03:36Now, we will check
03:38this one.
03:40Look at this.
03:42This is dead.
03:44This is dead.
03:46This is SMD dead.
03:48Now, we will change this.
03:50After that, we will check the kit.
03:52What is the problem in the kit and what is not.
03:54First of all, we will check this.
03:56This is dead.
03:58Now, we will remove this.
04:00Now, we have done the communication.
04:02We have adjusted this in the box.
04:04Now, the problem is that
04:06everything is ok in this.
04:08Now, I have started to run this.
04:10Now, we will check
04:12whether the fault is cleared or not.
04:14Now, there will be
04:16some noise in the sound.
04:18I am sorry.
04:20That is because we have kept the fan
04:22down because if we have to
04:24turn on the compressor for a long time,
04:26then I will keep it down so that
04:28the IPM does not heat up.
04:30I have turned it on.
04:32As soon as it turns on, I will show you.
04:34We have changed the SMD which I
04:36showed you. It was dead.
04:38The rest of the kit is original.
04:40As I told you,
04:42if there is such a problem,
04:44there will be starting trouble.
04:46The IC that I told you,
04:48you have to check the SMD
04:50next to it.
04:52There are six SMDs.
04:54You have to check all six SMDs.
04:56If there is any fault in it,
04:58then this problem arises.
05:00Only one SMD was dead.
05:02Because of which this fault came.
05:04If any brother wants to learn work,
05:06he can come and take training
05:08from us here.
05:10Subscribe to the channel
05:12and like it.
05:14So many people watch the video.
05:16This is our way of seeing
05:18that nothing happens to you
05:20that we do not tell you.
05:22We tell you everything clearly.
05:24Do try to like it.
05:30Look at this.
05:32The compressor
05:34has started.
05:36Now
05:38the way to check it
05:40with confidence is
05:42that this fan is installed.
05:44You will feel a little noise in the voice.
05:46But it is compulsory.
05:48I have turned it on.
05:50Our kit is running.
05:52And now the compressor
05:54as I showed you earlier,
05:56it was immediately closed.
05:58Now the RPM has increased.
06:00It has gone to full RPM.
06:02Look at this.
06:04You can feel it.
06:06And how fast the RPM is full.
06:10The video will be a little long.
06:12But now I will show you
06:14that now it will not be closed.
06:16Look at this.
06:18I changed the SMD.
06:20I also showed you that in front of you.
06:24Look at this.
06:26Now it is full RPM.
06:28Because if the RPM is full,
06:30you can hear the sound.
06:32Look at this.
06:34Look at this.
06:36You can hear the sound.
06:38Look at this.
06:40I have put full load on it.
06:42Look at this.
06:44Look at this.
06:48Now our kit is OK.
06:50Now our kit is OK.
06:52If you like the video,
06:54then like it.
06:56Thank you for watching the video.
06:58Goodbye.
Comments