00:00Now, proceed to group, press Ctrl-G, or you can go to the Utilities menu, then select Group.
00:08Right now, we only need the trusses, so in the dialog box under Group, select Trusses, then click Highlight.
00:18Now we create new groups, and this time we will group the truss by its direction.
00:23To make naming short and clean, we'll use the axis X, Y, and Z.
00:36We'll start with the Z direction, so this would be our Z1, Z2, Z3, Z4, Z5, and Z6.
00:46Next is for diagonal trusses. Name them D1, D2, D3, and D4.
00:52Since we have four diagonal trusses, then, for the X direction, name them X1 and X2, since we have two
01:02trusses in the X direction.
01:03Now, name all of these groups first before we assign.
01:07Same process of naming, just like what we did a while ago.
01:10Click Create. Select Type Beam, then name it, using the naming guide, then click OK.
01:22Go find Mrs. T5, Z4, Z4, Z4, Z4, Zzag, and Z6, Z4.
01:49Now close to our names.
01:51naming we are now going to assign.
01:57Let's start with the diagonal trusses. First is D1, select it. Then assign.
02:04Always double-check for short length beams that might get missed.
02:25Like this one. In top view it seems like it's already selected, but a short beam isn't included.
02:31So be careful and always double-check. Now assign it to D1.
02:59Next, assign for remaining diagonal trusses for D2, D3, and D4.
03:22An important part to keep the diagonal trusses for D2, D2, and D3.
03:22If you look at the diagonal trusses for D2, D3, it's just a short break.
03:25I'm gonna pull that off you and see what you see after D3, D3.
03:25And like this one. Next we have a D3 to D3.
03:39Now add a few cases that are D4.
04:13Now, we are done assigning all diagonal trusses.
04:16We are now going to proceed on assigning X and Z direction.
04:28First go to the Select menu, then under Attribute Category, Select Group, a dialog box will appear.
04:34Now if you notice, only the groups we've already assigned, D1 to D4, appear here.
04:39That's because only the assigned groups will show in this dialog box.
04:43Now select D1, D2, D3, and D4.
04:49This is the best and fastest way to highlight the groups we already assigned.
04:53Again, always double check to make sure everything is grouped correctly.
05:13Now display the whole structure again, then highlight all the diagonal trusses.
05:18Now select the unos.
05:19Then select how to possibiluted the strings.
05:22Now display like this.
05:28So click on the align
05:28Like this, you can see it tedesk.
05:32It will apply it for this one as possible.
05:32Zonelet with phrases укặc email address shouldell true response.
05:32and then delete it iTunes when there's or if you areена have growth likely to determine
05:34And then note as possible, that only if you want to multiply.
05:36See this, you can see number three Louisvilleving way back slide, shown over the
05:48uphill, which if the two teams have erected together.
05:48So don't require high around the past.
05:50Next, click Inverse, then go to New View and switch to Top View.
06:03Now select the X1 truss, then assign it.
06:22Next, select the X2 truss, then assign it.
06:51Now highlight X1 and X2, then inverse select.
06:55This time we're selecting everything else along the Z direction trusses.
06:59Same process of assigning, select Z1, then assign select Z2, then assign select Z3, then
07:06assign select Z4, then assign select Z5, then assign lastly, select Z6, then assign
07:48a set type.
07:48Now list.
07:48Next, select Z1, then add the X2.
07:48Next, select Z4, then assign select Z1, then assign select.
08:05Now we're done grouping our trusses based on direction.
08:08This is our part 2 for grouping.
08:10We still have the next part for grouping, so save first before we proceed on the next
08:15part.
08:18Here we go.
08:28You
Comments