iPhone 13 Screen Replacement： DIY Guide to Restore Your Display!

Sara Totoy - Desenhos Infantis

Transcript

00:00To begin the repair, we'll take the pentalobe screwdriver and remove the two bottom screws from the device.

00:11We'll then take the single-sided razor blade and create a gap between the edge of the screen and the chassis of the device,

00:20and then carefully pry upwards to create a larger gap, which will now be big enough to insert our guitar pick into,

00:26where we can slide it through this right-hand edge, the bottom edge, and the left-hand edge.

00:38Once you've lifted it away from the sides and the edge, we're going to wiggle the phone a little bit from side to side,

00:45holding it from the bottom, and then open up the screen, just like opening a book.

00:51And we can see this one is actually very wet inside.

00:53So the first thing I'm going to do is start to dry it out with the hot air gun and a microfiber cleaning clock.

01:04We don't know if the liquid has done any further damage already,

01:07but I'll proceed with the repair and test it out once the screen's been replaced.

01:11We can now take the cross-head screwdriver and remove the three screws that hold the shield in place for the screen connector and the battery.

01:18Once they're unscrewed, take your tweezers and lift the shield out of the way.

01:24Then using the plastic spudger, it's important to isolate power from the device by disconnecting the battery.

01:29Now there's no power running through the device, it's safe to disconnect the front screen connector, which is this one here.

01:34Now we'll move up to the top of the device and remove the single cross-head screw from the middle of the shield,

01:40the tri-wing screw in the top right,

01:42and the other cross-head screw in the top left

01:48to lift up the shield,

01:52and the spudger to disconnect this flex cable here.

01:56That means that we can now remove the screen from the phone

01:58and begin working on cleaning up the chassis, ready for the new screen.

02:02We need to remove the old water-resistant seal from this one

02:05and to do that, take your tweezers

02:07and begin lifting up and peeling away

02:12the spent adhesive seal.

02:16On all models of iPhone after the iPhone 12,

02:19these did get a little bit more awkward,

02:21so just take your time with this and get as much of it away as you possibly can.

02:25Once all the seal's removed, we're going to take some isopropyl alcohol now,

02:34apply it to the edge of the chassis,

02:38and then using the cleaning brush,

02:40brush away any dirt, dust, and grime that's left behind.

02:45Repeat the same process to all edges of the phone,

02:49making sure to get in all the nooks and crannies of the chassis.

02:52Be careful when you're cleaning out this top edge

02:54because you don't want to nudge the Face ID infrared camera

02:58or front camera sensor.

03:03With that now cleaned,

03:05we can take our new adhesive seal

03:08and apply that to the chassis,

03:11starting in the top left corner,

03:13lining up the left-hand edge

03:15and then making sure that it sits nice and flush

03:18all the way around the device.

03:27Once it's laid flat,

03:29use the back end of the spudger

03:30just to push it down

03:32and make sure that it's sat

03:34really nice and neat

03:35all the way around.

03:36Then peel away this top layer of the film

03:44and that's now ready to receive the new screen.

03:49We'll put that down to one side

03:50then go back to this damaged screen

03:52and using the tri-wing screwdriver this time

03:54remove the three screws holding down this shield here.

03:58Use your tweezers to lift the shield

04:10and then using your heat gun or hairdryer

04:13we're going to warm up this flex cable here

04:16so that we can soften the adhesive

04:20making it easy to pull away

04:22that little cable.

04:29Once that's heated

04:30and the adhesive is softened

04:32we're going to get those tweezers again

04:33and starting from this area here

04:37start lifting up this flex cable

04:39enough so that we can get our thumb

04:41underneath it here

04:42to peel it away

04:44from the back of the display.

04:55Once that's peeled off

04:56we're going to go back to the sensor area

04:58just over here

04:59and lift the proximity sensor first

05:04then allowing the heat to do its thing

05:06we're going to lift up

05:07the proximity sensor

05:11and the ambient light sensor.

05:15Now taking the new screen

05:16we'll peel off these protective

05:18peel stuff

05:20off the back of the display

05:21then start by realigning the ambient light sensor here

05:28proximity sensor and microphone

05:30and then that should allow

05:32the rest of the flex cable

05:35to line up

05:36exactly where it needs to be.

05:38finally there's just that little shield

05:46and the three

05:47tri-wing screws to re-secure

05:51and once they're secured into place

06:10this screen is now ready to reinstall

06:13into our chassis

06:13the easiest way to do this

06:15is by offering up the screen connector first

06:19making sure that that sits into place

06:21then get the front sensor cable

06:23and secure that

06:25and then reattach the battery connector

06:28we can now realign this shield

06:33that goes over the top flex cables

06:35of the motherboard

06:35re-secure the cross head screw just here

06:39the tri-wing screw just here

06:53and the cross head screw

06:54in the top left

06:56moving back down

07:01we're going to reinstall the shield

07:02for the screen and battery

07:04which is held down by the three cross head screws

07:08we can now remove that final layer of the peel

07:21for the adhesive seal

07:22this usually comes off in two or three pieces

07:32and to get the final piece you have to fold down the screen

07:35and peel it away

07:41to re-secure the screen into place

07:43go ahead and install the top part of the screen first

07:46and work your way down

07:47re-securing it back into the chassis

07:51before finally reinstalling the two pentalobe screws

07:58at the bottom of the phone

07:59that just about completes the repair

08:09with this iPhone 13 front screen

08:11thank you for watching and see you next time

08:15that we have to do it

08:23and then at the bottom of the screen

08:26and see you next time

08:26we don't see you next time

08:27if you start doing a demo

08:28and then we see you next time

08:29and then we're going to see you next time

08:30and we see you next time

08:32and then we're going to see you next time

Categoria

Transcrição

Recomendado