00:00okay i got it inside here now it's about the part numbers i've been looking for the part number
00:07oh and uh i keep forgetting to say you could subscribe if you want i got 14 subscribers
00:16and about 120 videos since the summertime okay so i was looking at uh that right there says
00:29719-0319 but it it looked pretty uh similar to the one i found where you get both halves for 58
00:44dollars on ebay and nine dollars shipping was about the cheapest i could find
00:51um problems all right so i think that was a real bolt in there right uh here
01:03was just a thread i took a nut from one of the new pegs and i put it on to see if i could get it out
01:11so i gotta punch that out somehow that might take some time these blades are pretty much shot but it
01:19works okay so i'm gonna probably go ahead uh i asked the guy on ebay if uh those part numbers
01:28would work because i guess there's like uh a hundred other machines it works with and it is mtd
01:36uh problem number two here i'm trying to get this this was over there i'm trying to get this half off
01:46um i tried a hammer um i tried sanding down the pipe here
01:55um but now a closer look at the gear
02:01it still looks pretty good and it didn't come off the uh it's not moving
02:09so i'm gonna probably just keep it just like that uh if i can take the other side off and get this part off
02:18it's stuck on something but now i noticed on the inside
02:32there seems to be
02:34wonder if that has to be
02:37pulled out
02:38maybe that's the reason it's not moving
02:41anyhow this is part three
02:47this came off okay
02:50i'll probably have to get a new peg
02:52you got the washer there
02:57this plastic sleeve part here
03:01um
03:04under here you see
03:06this came off
03:08just like this
03:10so that's uh
03:13i believe it was like that
03:17yeah
03:18and a mess of grease on the inside
03:24so i'm gonna try to get this part off but i'm gonna pause this
03:32and then i'd let you know you know what i did to get it off
03:37okay so i just used a hammer to move it to show you
03:41there's a groove right there
03:44but
03:46i don't see any reason why
03:48this shouldn't
03:50slide right off here
03:52so
03:54i'm gonna try it again
03:56success
03:58okay so what i did was
04:01put this here
04:04i just kept hitting this
04:07and then on the top
04:09equally
04:11until it
04:17also put little
04:19wd-40 on the end
04:22i mean you're gonna use the regular thick grease
04:26still gotta find out what type of grease is
04:29use
04:29thick machine
04:32this side's off now
04:35okay well that was
04:39pretty hard right to the end
04:41before it popped off
04:43and then i still have this piece
04:45and that's a part again with the sleeve let me clean it off a bit
04:56it's a sleeve there
05:02so
05:06anyhow there's the
05:11part number
05:13the uh
05:16it's made in usa
05:19it's the other half there
05:25okay that's gonna
05:27so i'm gonna work on the bolt here
05:29to get that off
05:32and be back
05:34going back to this
05:38i did get it off
05:39just be careful hammering
05:41equal
05:42each sides
05:43or probably you could just sand that
05:45have a little
05:46sandpaper here
05:48sand that down
05:50probably slide off
05:52put some grease on it
05:53slide off a little easier
05:54um
05:55and then
05:55now i'll work on that bolt
05:57alright so i gave up on the hammering
06:00and uh
06:03in one of my last
06:05videos with the peg
06:07now i'm
06:10going to drill
06:13drill it out
06:30see if we got any
06:33lock
06:35here
06:38it's stubborn that's for sure
06:58but it worked for the peg
07:09i think this is a real bolt in here
07:12there's no peg in here
07:14so
07:25so
07:27so
07:29so
07:31so
07:39I'm going to finish this.
