00:00Oh
00:14Peace be upon you
00:16Who this kid is sheng hung rovers this one the problem with it is that the motor and it doesn't turn on when the blow motor is turned on
00:23But we will check what is the problem why is it not turning on and what could be wrong with and you will check it completely
00:34This is the kid plate in front of you the main problem. I have but this thing is that you know it's other
00:43So you can make it work better
00:46If you don't know the second how it's going to work out what it is then you don't work
00:50Can we see the kid from here so seen it that would it?
00:56These are that
01:00This is an auto coupler, but it claims it isn't one the number is I
01:07Check this number is this the right number?
01:10This is equipped with an auto coupler this contains several and mock numbers
01:24It has a tracker installed for satellite tracking now
01:32Ensure it's kept safe
01:34I
01:36In T loan
01:38Lizardo is present and I mentioned it to Casey
01:42What is its function in the new manner?
01:49Check it out the equipment is working fine running starts in three
01:55My movie is fully made on the motor you can check it out here
01:59The line comes from here
02:03This common wire runs straight here from the start
02:08Look here from the drag
02:13This is the main wire connecting to the common here
02:18Now if you see this is its gate with the MOSFET and track
02:21It is the gate here. There is an auto coupler you need to switch on this side
02:37Along with this there is a pop of video made for each component showing how it works with our micro processor
02:42This wiring connects here and you will see the current coming from here
02:59This wiring connects here and you will see the current coming from here
03:04Current comes here and any connected motor or switch will turn on
03:16First we need to check if voltage is coming here or not
03:27This is a micro processor pin number four connects here to receive pulses
03:34So
03:36So it will receive current at pin four it will work with this the auto switch will start turning on
03:49The rpm is controlled from here adjusting speed with these pulses
03:59It occurs
04:01Now we will check out the pulses this track will see function and why the motor isn't starting
04:11I will check this in front of you and let you know
04:14Initially, I have a video prepared on this side you can view
04:21This part here is the ground right
04:24This is this positive side and then there's the ground and VZ okay
04:27It's showing turbo
04:31You accept for two pins the pin in front of these pulses and when it does it will output current on the other side
04:41And along with this we will see how to check it here now
04:43I will start checking it first we need to see if pulses are coming from here
04:51First we will check the pulses from here the method to check this is to use the diesel
04:55So
04:58Check the diesel plug while I show you
04:59I connect the current with it just as I did in the ground
05:04I remain here with it and I will check it with the DSO from this point
05:09Are the pulses coming or not?
05:12This is our DSO
05:14When I give it voltage, you will see the line straight here
05:18Look it's a straight line when I give it a pulse
05:24We will see how it works with the auto like this plug
05:28I do it current is here check it
05:35The current has come here now
05:40Current is here
05:41I will do this
05:43It's on here
05:49When the motor turns on here you will see the pulses start coming
05:57See pulses are coming
05:59I have checked this and I will demonstrate how to verify it with the meter to see if the connection is straight or if there is another issue
06:06Now the junction here I have begun
06:08Here it is at that time
06:13Just like the pulse stop did happen at that moment
06:19This means that our DO is fine
06:21There is absolutely no issue with it and there is no problem of any kind
06:24Now we will check after the micro plus I will show you how it displays the output and what variations it has
06:35Look we see how this works
06:39Look at this pin you can see that there are one two three four is for number pin
06:48It is here now this auto copper is connected here
06:55Because you see the phone number pin
07:01Look
07:04Here's the auto coupler and the IC is below
07:07They put a jumper here and look it's here
07:10I'll show you the jumper
07:13Here's the jumper it's attached here
07:17See this the buzzer is coming now
07:20Look at the pin numbers 1234 it needs to be auto here clearly
07:27You have four here so it will be four here
07:31One two three four the pin is here and it turned to connect
07:37Look here it's being taught
07:40After this we will connect here and take you to the microprocessor
07:45Okay, look at this micro this is the micro
07:49Now the microprocessor check out this pin
07:54Check this pin it has a connector
07:57This pin here we we are receiving a signal here indicating that the motor should now operate and so far everything is okay
08:05But how do we check the missing pulses the voltage will provide you with pulse
08:09We can verify that using a meter
08:16See i'm providing current now
08:18Now so this meter too
08:20See i will touch this point and the other one here since the positive will go straight this is ground and it will connect look it is on there but see
08:27The meter has not shown current this means our ig is 40
08:35This is why the motor is not starting now we will turn it off
08:40After turning it off i will remove this ig in front of you after removing it we will install a new ig and then the motor will turn on
08:49See i am beginning to remove this now all that
08:51Now after removing this we will install a new one and i will show you all the motor runs along with the other side
08:59I show if it came out
09:02See we have taken the ic now i'll install the new ic and show you once more
09:09We will now install the new ic i had it on top look i took it
09:15Now about the ic see how to install it there's a doubt and a wish all right
09:20This is the straight side we will paste it here first this is the initial task let's apply the paste
09:27I'm starting to apply the paste first see i've applied it on top all right just apply it without worries
09:34There's no issue with the paste because if it's applied it will stick better and your joint will never be loose
09:42Now i'm placing this on top see there's no issue with the ic
09:51Look there's no issue with the ic look there's no problem with the ic
09:56If you want to subtle but very little because of the microscope you can see
10:12Clearly otherwise it is not so clearly visible on the common port
10:21If you want to it is possible but very little
10:39This is it
10:49Maxiscope because of you
10:56Looking if you want to it's tangible but very little it is tangible but very little
11:00This isn't ready yet once this kit is off we need to check the problem our hub is now online and look it's voltage is
11:11The wires have come here so this lotion has become current
11:16Our kit is now okay and should
11:19Now let's check this hub again i'll turn it on and check it for you look here it's fine it's here
11:23Okay
11:30The voltage is full here now our kit is fine
11:34This is the method to check the kit to see it's voltage i have also changed this ive in front of you
11:40This will make your motor run and beyond thank you if you enjoyed the video like share and subscribe to our channel
Comments